LED Strip Light Accessories - LED Strip Connectors & Wires

Double Door Switch Sensor 12v/24v

Oliver King — Wed, 11 Dec 2024 15:32:22 +0000

Slim-line low voltage double door switch sensor. Ideal for use in double wardrobes, drawers or areas where lighting is only required when a door is opened. Comes with a surface mounted bracket, or it can be recessed into a surface. The sensor should be mounted in the center of the lighting space where contact can be made with both doors. The double door switch sensor has 2 positive and 2 negative inputs and outputs. This means the sensor can control 2 separate sides of a cupboard or wardrobe. The connection leads are 1m long. When the sensor is blocked by a door or surface, the LEDs will be turned off. Once the sensor has a clear line of sight, the LEDs will be turned on.

The switch is suitable for 12-24V circuits. Upto 80w can be powered at 12v at 120w can be powered at 24v.

The post Double Door Switch Sensor 12v/24v appeared first on LED Lighthouse.

Door Switch Sensor 12v/24v

Oliver King — Wed, 11 Dec 2024 15:07:47 +0000

Slim-line low voltage door switch sensor. Ideal for use in cupboards, wardrobes, drawers or areas where lighting is only required when a door is opened. Comes with a surface mounted bracket, or it can be recessed into a surface. The door switch sensor has a positive and negative on both the input and output. The connection leads are 1m long. When the sensor is blocked by a door or surface, the LEDs will be turned off. Once the sensor has a clear line of sight, the LEDs will be turned on.

The switch is suitable for 12-24V circuits. Upto 80w can be powered at 12v at 120w can be powered at 24v.

The post Door Switch Sensor 12v/24v appeared first on LED Lighthouse.

Infared PIR Sensor 12v/24v

Oliver King — Wed, 11 Dec 2024 14:47:20 +0000

Slim-line low voltage PIR. Ideal for use in pantrys, wardrobes or areas where lighting is only required where motion is detected. Comes with a surface mounted bracket, or it can be recessed into a surface. The PIR sensor has a positive and negative on both the input and output. The connection leads are 1m long. Once activated, the PIR sensor will keep the LEDs illuminated for circa 30 seconds.

The switch is suitable for 12-24V circuits. Upto 80w can be powered at 12v at 120w can be powered at 24v.

The post Infared PIR Sensor 12v/24v appeared first on LED Lighthouse.

Solid LED Strip to Strip Connector COB 2 Pin

Oliver King — Fri, 31 May 2024 10:44:39 +0000

This connector is used to connect two lengths of our 10mm white COB LED strip together. The LED strip light must be 10mm wide to use this connector. Before this connector can be used, gel waterproof coatings must be removed 7mm from the end of both LED strips. The LED strip can then slide inside the connector, passing under the metal arms. Ensure the arms are pushing down onto the copper contacts of the LED Strip.

This connector can be used with our Nano Tech LED Strip providing the thin waterproof coating is removed from the top of the copper terminals first. This can be done using a sharp blade or fine sandpaper.

The price is for 1 connector only.

This connector is only suitable for connecting up to 5m of LED strip. To power longer lengths a soldered connection is required.

Please note, this connector can only be used with our 12v or 24v white COB LED strip light.

The post Solid LED Strip to Strip Connector COB 2 Pin appeared first on LED Lighthouse.

Flexible LED Strip to Strip Connector COB 2 Pin

Oliver King — Fri, 31 May 2024 10:40:22 +0000

This connector is used to connect two lengths of our 10mm wide, white, COB LED strip together. The LED strip light must be 10mm wide to use this connector. Before this connector can be used, gel waterproof coatings must be removed 7mm from the end of both LED strips. The LED strip can then slide inside the connector, passing under the metal arms. Ensure the arms are pushing down onto the copper contacts of the LED Strip.

This connector is approximately 300mm long.

This connector is only suitable for connecting up to 5m of LED strip. To power longer lengths a soldered connection is required.

Please note, this connector can only be used with ouw 12v or 24v white COB LED strip lights.

The post Flexible LED Strip to Strip Connector COB 2 Pin appeared first on LED Lighthouse.

90 Degree LED Strip Corner Connector COB 2 Pin

Oliver King — Fri, 31 May 2024 10:32:30 +0000

This connector is used to connect two lengths of our COB single colour LED strip lighting together at a 90 degree corner. The COB LED strip light must be 10mm wide to use this connector. Before this connector can be used, gel waterproof coatings must be removed 7mm from the end of both strips. The LED strip can then slide inside the connector, passing under the metal arms. Ensure the arms are pushing down onto the copper contacts of the LED Strip.

The price is for 1 connector only.

Please note, these connectors are for the 12v and 24v COB strip in white only.

The post 90 Degree LED Strip Corner Connector COB 2 Pin appeared first on LED Lighthouse.

Solid LED Strip to Strip Connector COB RGBW 12mm 5 Pin

Oliver King — Tue, 28 May 2024 14:33:32 +0000

This connector is used to connect two lengths of our RGBW colour changing LED strip together. The LED strip light must be 12mm wide to use this connector. Before this connector can be used, gel waterproof coatings must be removed 7mm from the end of both LED strips. The LED strip can then slide inside the connector, passing under the metal arms. Ensure the arms are pushing down onto the copper contacts of the LED Strip. Then close the connector cover, ensuring the teeth clamp directly onto the circuit board of the LED strip not the gel coating.

This connector is only suitable for connecting up to 5m of LED strip. To power longer lengths a soldered connection is required.

This connector is only suitable for the RGBW COB LED strip lights.

The post Solid LED Strip to Strip Connector COB RGBW 12mm 5 Pin appeared first on LED Lighthouse.

Flexible LED Strip to Strip Connector COB RGBW 12mm 5 Pin

Oliver King — Tue, 28 May 2024 14:15:04 +0000

This connector is used to connect two lengths of COB RGBW colour changing LED strip together. The LED strip light must be 12mm wide to use this connector. Before this connector can be used, gel waterproof coatings must be removed 7mm from the end of both LED strips. The LED strip can then slide inside the connector, passing under the metal arms. Ensure the arms are pushing down onto the copper contacts of the LED Strip. Then close the connector cover, ensuring the teeth clamp directly onto the circuit board of the LED strip not the gel coating.

This connector is approximately 300mm long.

This connector is only suitable for connecting up to 5m of LED strip. To power longer lengths a soldered connection is required.

This connector is only suitable for the COB RGBW LED Strip lights.

The post Flexible LED Strip to Strip Connector COB RGBW 12mm 5 Pin appeared first on LED Lighthouse.

LED Strip Power Lead Connector RGBW 12mm 5 Pin

Oliver King — Thu, 20 Apr 2023 10:22:29 +0000

This connector is designed to clip onto the end of our RGBW colour changing LED strip. The LED strip light must be 12mm wide to use this connector. Before this connector can be used, gel waterproof coatings must be removed 7mm from the end of the LED strip. The LED strip can then slide inside the connector, passing under the metal arms. Ensure the arms are pushing down onto the copper contacts of the LED Strip. Then close the connector cover, ensuring the teeth clamp directly onto the circuit board of the LED strip not the gel coating.

This connector is approximately 150mm long.

This connector is only suitable for powering up to 5m of LED strip. To power longer lengths a soldered connection is required.

The post LED Strip Power Lead Connector RGBW 12mm 5 Pin appeared first on LED Lighthouse.

COB LED Strip Power Lead Connector 10mm 2 Pin

will — Thu, 07 Jul 2022 08:32:07 +0000

This connector is designed to clip onto the end of our single colour 10mm COB LED strip to allow it to connect with a 12/24V power supply. The COB LED strip light must be 10mm wide to use this connector. Before this connector can be used, gel waterproof coatings must be removed 7mm from the end of the LED strip. The LED strip can then slide inside the connector, passing under the metal pins. The pins can then be pushed down using a pair of pliers to clamp the COB LED strip light in place. The wired connection can also be clamped in the connector, ensuring the teeth clamp directly onto the circuit board of the LED strip not the gel coating.

The post COB LED Strip Power Lead Connector 10mm 2 Pin appeared first on LED Lighthouse.